New Samson 510 table new options
-
- 1/2 Star Member
- Posts: 3
- Joined: Tue Mar 19, 2019 12:44 pm
New Samson 510 table new options
Just got a Samson 510 table , hypertherm 65 ,with design edge software. With my old trucut table and software I could click "run from here" and start where the table stopped or missed a cut even if it went through the whole file, so my question is how can I do that with my new machine. Thank you.
-
- 3 Star Member
- Posts: 313
- Joined: Tue Jul 28, 2009 11:23 pm
- Location: Weiser, ID
- Contact:
Re: New Samson 510 table new options
I am probably not understanding your question correctly, but if my torch misfires a thing comes up on the computer screen asking me if I want it to continue cutting from where it last stopped cutting or something like that.
-
- 4 Star Elite Contributing Member
- Posts: 1184
- Joined: Tue Aug 25, 2015 12:05 pm
- Location: Central MO, USA
Re: New Samson 510 table new options
Samson is the same as Plasmacam, so asking Plasmacam users may find your answer.
Bulltear 6x12 w/ Proton Z axis & watertable
CommandCNC/Linux w/ Ohmic & HyT options
Hypertherm Powermax 85 w/ machine torch
Solidworks, Coreldraw X7, Inkscape, Sheetcam
CommandCNC/Linux w/ Ohmic & HyT options
Hypertherm Powermax 85 w/ machine torch
Solidworks, Coreldraw X7, Inkscape, Sheetcam
- rdj357
- 4 Star Elite Contributing Member
- Posts: 1185
- Joined: Sun Mar 11, 2012 4:40 pm
- Location: Tahlequah, OK
Re: New Samson 510 table new options
If a red dot comes up and you don't unselect the remaining to cut paths, it will ask you if you'd like to resume where cutting stopped.
If you're trying to finish a bunch of cuts and have either accidentally unselected the remaining cuts or otherwise need to continue from one path to the end, here's a video I did. This topic starts at 30 minutes in.
https://www.facebook.com/learnplasmacam ... 003642722/
If you're trying to finish a bunch of cuts and have either accidentally unselected the remaining cuts or otherwise need to continue from one path to the end, here's a video I did. This topic starts at 30 minutes in.
https://www.facebook.com/learnplasmacam ... 003642722/
Robert Johnson
PlasmaCAM GURU & Instructor
I am not affiliated with PlasmaCAM, Inc. in any way. I offer training on their equipment and software. All product and company names are trademarks™ or registered® trademarks of their respective holders. Use of them are for nominative purposes only and does not imply any affiliation with or endorsement by them.
PlasmaCAM GURU & Instructor
I am not affiliated with PlasmaCAM, Inc. in any way. I offer training on their equipment and software. All product and company names are trademarks™ or registered® trademarks of their respective holders. Use of them are for nominative purposes only and does not imply any affiliation with or endorsement by them.
-
- 1/2 Star Member
- Posts: 3
- Joined: Tue Mar 19, 2019 12:44 pm
Re: New Samson 510 table new options
Thank you, I wanted to start just a little bit before it stopped. But still have not figured out how to go back. With the trucut table I can go to a specific spot and recut a place that did not cut correctly. Thanks for the help.
-
- 1/2 Star Member
- Posts: 1
- Joined: Tue Dec 25, 2018 4:14 am
Re: New Samson 510 table new options
Restart the cut but before it fires hit stop on the controller and then use the shuttle dial to track along the cut line. This makes the machine follow the cut path. Once you track to where u want to start. Hit the start button. Hope this helps