Issue with limit switches when powering on table

Share and learn with other DIY members who have built their own plasma tables and accessories.
Post Reply
Pdtwrs
1/2 Star Member
1/2 Star Member
Posts: 1
Joined: Mon Dec 20, 2021 10:06 am

Issue with limit switches when powering on table

Post by Pdtwrs »

Hi Everyone,

I have a Thermal Dynamics Cut Master 82 table, running Mach 3 software.

We have the table running properly except for the limit switches. The Emergency Stop and the table switches are all serially wired together with normally closed as the operating mode. Any break from any switch will stop the table. Mach 3 is setup with the x, y, z and Emergency Stop settings all the same because there is only one input to the Bob Board from the table. The low indicated is activated in the Config - Ports, Input tab. The limit switches work properly if power to the table is turned off. When the power to the table is turned on, it switches to normally open instead of normally closed as the operating mode. Why would powering on the table change the limit switch operating mode for normally closed to normally open?

Thanks in advance for your help,

Phillip
weldguy
4.5 Star Elite Contributing Member
4.5 Star Elite Contributing Member
Posts: 2187
Joined: Fri Apr 17, 2009 11:48 am

Re: Issue with limit switches when powering on table

Post by weldguy »

Hmmm, curious myself.

Is your computer using a parallel port connection?

When you say the limit switches work properly when table power is turned off are you determining this by seeing an on screen indicator in Mach3 responding to switch input?
User avatar
djreiswig
4.5 Star Elite Contributing Member
4.5 Star Elite Contributing Member
Posts: 2024
Joined: Thu Nov 19, 2015 10:02 pm
Location: SE Nebraska

Re: Issue with limit switches when powering on table

Post by djreiswig »

Is there a relay in the loop that is switching when it is powered up?
2014 Bulltear (StarLab) 4x8
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
adbuch
6 Star Elite Contributing Member
6 Star Elite Contributing Member
Posts: 10135
Joined: Thu Sep 21, 2017 5:22 pm
Location: Tucson, Arizona
Contact:

Re: Issue with limit switches when powering on table

Post by adbuch »

Perhaps you have them wired wrong, or you have the wrong type of switch. If they have both NO and NC terminals, make sure you are connecting to the correct ones for your application. It is also a possibility that you have a choice in your software as to NO or NC and you have the wrong box checked.
David
User avatar
acourtjester
6 Star Elite Contributing Member
6 Star Elite Contributing Member
Posts: 8183
Joined: Sat Jun 02, 2012 6:04 pm
Location: Pensacola, Fla

Re: Issue with limit switches when powering on table

Post by acourtjester »

His problem was a ground loop, now working fine.
DIY 4X4 Plasma/Router Table
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
adbuch
6 Star Elite Contributing Member
6 Star Elite Contributing Member
Posts: 10135
Joined: Thu Sep 21, 2017 5:22 pm
Location: Tucson, Arizona
Contact:

Re: Issue with limit switches when powering on table

Post by adbuch »

acourtjester wrote: Sun Jan 02, 2022 9:34 pm His problem was a ground loop, now working fine.
:Like :Like :Like :Like :Like
Post Reply

Return to “DIY Plasma Table & Accessory Discussion Forum”