Plasma cut for my new downdraft Watertable Part 1

Post by **East German** » Sun Apr 13, 2014 6:40 am

Hallo,
my new Homebuild Plasma.

-working surface 1030 mm x 1550 mm
-two fans

Works very well no smoke in the garage!
Regards Peter

Post by **East German** » Sun Apr 13, 2014 6:44 am

Part 2

Post by **East German** » Sun Apr 13, 2014 6:51 am

Part 3

Exhaust is not finished

Regards Peter

Post by **Mr.Dirt** » Sun Apr 13, 2014 8:40 am

Looks like a great design.

Post by **tnbndr** » Sun Apr 13, 2014 10:55 am

Very nice job.
And look at that stacked house of firewood! It would take me a lifetime to get firewood to stack so neatly.

Post by **East German** » Sun Apr 13, 2014 11:10 am

tnbndr wrote:Very nice job.
And look at that stacked house of firewood! It would take me a lifetime to get firewood to stack so neatly.

Hallo Denis

If only outside a row of wood.
In the middle are Tractor and co

Regards Peter

Post by **tnbndr** » Mon Apr 14, 2014 9:25 am

Hallo Denis
If only outside a row of wood.
In the middle are Tractor and co

Ahhhhhhhhhhhhh, very tricky!!!

x5er30 · Post by **x5er30** » Thu Apr 17, 2014 10:16 am

I have a question...did you build tanks for the military? lol
Nice job, heavy duty is good. how does the downdraft work?
i went through many ideas to downdraft my custom built table
and just couldnt get the power i was expecting for my home garage
so i went back to a revised water pan ( all aluminum except cross grade slats)

Post by **East German** » Thu Apr 17, 2014 3:20 pm

x5er30 wrote:I have a question...did you build tanks for the military? lol
Nice job, heavy duty is good. how does the downdraft work?
i went through many ideas to downdraft my custom built table
and just couldnt get the power i was expecting for my home garage
so i went back to a revised water pan ( all aluminum except cross grade slats)

Hallo,

heavy duty is good, my old Watertable was 3 mm it s in the Time very bending.
The new Table is 5,5 mm Steel with 5 % Nickel, this steel is fore gas barrel!

The two fan makes about 1000cfm its very fine!

I think this is the correct construction,it is very much better than before with the old Watertable.

I am absolutely thrilled after a few days.

Regards Peter

Largemouthlou · Post by **Largemouthlou** » Sat Apr 19, 2014 8:11 am

VERY well done Peter!!!!!!!!!!!!!! Wish I had your patience and insite

pertneer · Post by **pertneer** » Sat Apr 19, 2014 8:51 am

Nice work. Should hold up very well over time. I see your table slats are a unique design. Do they slide along the length of the slats to the location you need for what you are cutting? Does slag build up to inhibit their movement?

Post by **East German** » Sun Apr 20, 2014 2:27 am

pertneer wrote:Nice work. Should hold up very well over time. I see your table slats are a unique design. Do they slide along the length of the slats to the location you need for what you are cutting? Does slag build up to inhibit their movement?

Hallo,
they slide along the length is 12 mm Steel.
The slag is removed with a hammer is very stable.

Regards Peter

Plasma cut for my new downdraft Watertable Part 1

Plasma cut for my new downdraft Watertable Part 1

Re: Plasma cut for my new downdraft Watertable Part 1

Re: Plasma cut for my new downdraft Watertable Part 1

Re: Plasma cut for my new downdraft Watertable Part 1

Re: Plasma cut for my new downdraft Watertable Part 1

Re: Plasma cut for my new downdraft Watertable Part 1

Re: Plasma cut for my new downdraft Watertable Part 1

Re: Plasma cut for my new downdraft Watertable Part 1

Re: Plasma cut for my new downdraft Watertable Part 1

Re: Plasma cut for my new downdraft Watertable Part 1

Re: Plasma cut for my new downdraft Watertable Part 1

Re: Plasma cut for my new downdraft Watertable Part 1